Shop headings: New Spares | Used Spares | Accessories | Brands
High tensile M8 bolt used to retain flywheel on big twins, used in drive box on V35 and V50. See ENA14901 for suitable washers.
Also known as Guzzi ref. 1206700 and 98054425. 6 bolts required for flywheel. Replaces flanged screw used on CARC models. Also used for retaining rear brake disc cover on V35 and V50 (7 bolts required)
More than 5 in stock
12067701-z 12067701 GU12067701 12 06 77 01
1206 7701 1206.7701 12.06.77.01
£0.90
INC VAT
£0.75 EX VAT
Output oil seal for drive box
This oil seal fits output side of bevel box
More than 5 in stock
90407085-z 90407085 GU90407085 90 40 70 85
9040 7085 9040.7085 90.40.70.85
£14.00
INC VAT
£11.67 EX VAT
Front crank oil seal for models with Bosch or Ducati charging systems
Also known as Guzz ref. 90402839
More than 5 in stock
90402840-Z
£9.50
INC VAT
£7.92 EX VAT
Side Panel Badge Clip
Also for mounting side panel trim on small twins. Supplied as round or rectangular clip
More than 5 in stock
39922200 GU39922200 39 92 22 00
3992 2200 3992.2200 39.92.22.00
£1.00
INC VAT
£0.83 EX VAT
Dimensions:
56mm length
Crownwheel bolt tab washer, two holes
More than 5 in stock
12356400 GU12356400 12 35 64 00
1235 6400 1235.6400 12.35.64.00
£3.90
INC VAT
£3.25 EX VAT
M6 wavy washer
Also known as Guzzi ref. 95129115
More than 5 in stock
03013800 GU03013800 03 01 38 00
0301 3800 0301.3800 03.01.38.00
£0.90
INC VAT
£0.75 EX VAT
Oil pressure sender, M12 thread, male bullet connector
Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.
See ENA12640 for replacement crush washer if required
More than 5 in stock
17768750 GU17768750 17 76 87 50
1776 8750 1776.8750 17.76.87.50
£10.00
INC VAT
£8.33 EX VAT
M10 schnorr washer, many applications
Anti vibrate washer. Also known as AP8152220
More than 5 in stock
19149800 GU19149800 19 14 98 00
1914 9800 1914.9800 19.14.98.00
£0.70
INC VAT
£0.58 EX VAT
Cartridge oil filter UFI 23 149 00
Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.
You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket).
Please note that Daytona RS and T5 Polizia use filter SIA15300
More than 5 in stock
14153000 GU14153000 14 15 30 00
1415 3000 1415.3000 14.15.30.00
£10.50
INC VAT
£8.75 EX VAT
A2 M6 x 40mm stainless steel socket cap screw
More than 5 in stock
£1.00
INC VAT
£0.83 EX VAT